日女人逼,日韩av免费在线观看,AV小网站,奶水孕妇挤胸喷奶水AV

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

trailer hydraulic cylinder Sold to Ecuador

Release time:2023-11-12 15:26:47 Hits: Current position: Home > News

This article mainly introduces:

Ecuador hydraulic cylinder,trailer hydraulic cylinder manufacturer,trailer hydraulic cylinder

Ecuador trailer hydraulic cylinder

(Ecuador trailer hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

trailer hydraulic cylinder are widely used in Ecuador,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed trailer hydraulic cylinder for customers from Ecuador.

Introduction to trailer hydraulic cylinder:

Classification of trailer hydraulic cylinder: according to the mode of movement it can be divided into linear reciprocating movement type and rotary swing type; According to the effect of liquid pressure, it can be divided into single acting type and double acting type. According to the structure, it can be divided into piston type, plunger type, multistage telescopic sleeve type, pinion and rack type, etc. According to the installation form can be divided into rod, earring, foot, hinge shaft and so on; According to the pressure grade can be divided into 16Mpa, 25Mpa, 31.5Mpa and so on.

trailer hydraulic cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the trailer hydraulic cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

Because of the slightly complex structure of the buffer trailer hydraulic cylinder, sometimes there will be problems, such as when the trailer hydraulic cylinder with the buffer device is started in reverse, the piston often stops temporarily or reverses. Elimination method: The orifice of the check valve is too small, so that the amount of oil entering the buffer chamber is too small, and even a vacuum occurs, so the above fault phenomenon will occur when the buffer plunger leaves the end cover. In this regard, the orifice of the check valve should be increased.

trailer hydraulic cylinder seal leakage causes and countermeasures: a. Loose tie rod nut will cause leakage, tighten the tie rod nut according to the torque requirements of tie rod nut, test no leakage can continue to use. b. Pressure exceeding the limit will also cause leakage. Replace the trailer hydraulic cylinder seal and re-tighten the tie rod nut to reduce the pressure to the nominal pressure range of the trailer hydraulic cylinder. c. The trailer hydraulic cylinder seal is extruded, if the O-ring is obviously extruded at the trailer hydraulic cylinder seal, replace the trailer hydraulic cylinder seal.

Answers to some questions about trailer hydraulic cylinder:

How big is the 100t cylinder pump and how big is the motor?
Load is calculated at 15 tons, stroke is calculated at 100 (both take the maximum) 15 tons = 15,000 kg, 15,000/210 bar (21 mpa) =71.42 square centimeters (cylinder area) 71.42/3,14 In the root *2=90,5 the inner diameter of the cylinder can be taken 100 mm. Travel 100 cm, that is, one meter, assuming 10, seconds a back and forth, then it is six times a minute, six meters per minute, then the required flow is,71,42*600 cm (6 meters) =42840 mm =42.84 liters/minute 42.84*21/60=14.9 kilowatts can choose 1450 RPM 4-stage motor 15KW.

How to use a solenoid valve to control the expansion of a cylinder? Doesn't the solenoid valve only control on/off?
Use the solenoid valve P into A-B (generally equipped with oil circuit board) to connect the oil inlet interface at both ends of the cylinder, and the solenoid valve can be realized by power off (refer to the solenoid valve 2B2L, different solenoid valve actions are different).

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
四虎一级片试看| 麻豆国产极品爆乳| 久久亚洲精品无码aⅴ| 熟妻无码| 四虎影院www| 国产欧美综合一区二区三区| 玖玖天堂色| 大香蕉一区二区在线视频| 久久久噜噜噜久久免费| 神马午夜福利| 中国小黄片| 手机看片 国产精品| 亚洲国产成人久久综合下载| 亚洲香蕉视频网| 最新亚洲精品| 欧洲精品乱码久久久久第1集| 国产小视频91| 国产特黄片| 欧美视频一区二区三区| 伊人久久精品一区二区三区| 国语对白系列| 91狠狠狠狠狠狠狠狠| 日日夜夜狠狠干| 久久久久久精品国产亚洲av麻豆| 伊人超碰导航| 国产情侣自拍网| 欧中黄片免费视频| 亚洲日本99| 青青伊人国语| 成人妇女免费播放久久久| 青青碰| overflow在线观看| HEYZO无码专区在线视频| 欧美亚洲中日韩综合| 久久aⅴ国产欧美74aaa| 亚洲国产精品lv| 亚洲精欧美一区二区精品| 综合区欧美区| 久久国产乱子伦免费无码| 五月婷婷久久一区综合国产_| 国产高清无码综合一本|