日女人逼,日韩av免费在线观看,AV小网站,奶水孕妇挤胸喷奶水AV

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

forklift tilting cylinder Sold to Korea

Release time:2023-11-12 15:29:22 Hits: Current position: Home > News

This article mainly introduces:

Korea hydraulic cylinder,forklift tilting cylinder manufacturer,forklift tilting cylinder

Korea forklift tilting cylinder

(Korea forklift tilting cylinder,produced by Hengyu Hydraulic Cylinder Factory)

forklift tilting cylinder are widely used in Korea,because of clever hydraulic energy conversion,no transmission clearance,powerful torque.So our company has designed forklift tilting cylinder for customers from Korea.

Introduction to forklift tilting cylinder:

The meaning of the forklift tilting cylinder model marked by the forklift tilting cylinder manufacturer: for example, 160/100-1150, its meaning: from a professional point of view, 160 refers to the forklift tilting cylinder diameter, which is 160mm, and the 100 behind refers to the rod diameter, which is 100mm. The 1150 refers to the forklift tilting cylinder stroke, which is 1150mm. Therefore, on this point, we should have a correct understanding and can not make mistakes.

After chrome plating of the piston rod of the forklift tilting cylinder, the surface flatness is not fully treated: After chrome plating of the piston rod surface, the method of post-plating polishing should be changed to post-plating polishing. Although it is necessary to increase the thickness of the coating before grinding (generally increased by about 0.02 in the diameter direction), it can remove chrome plating defects well, and test the binding force of the coating. In addition, due to the micro-roughness of the grinding surface, the trough can store lubricating oil, which can improve the wear resistance and extend the service life.

When the forklift tilting cylinder is in use, once the seal and guide support ring are found to be defective, the seal with the same structural form and appropriate material should be replaced according to the structural form of the forklift tilting cylinder seal to be repaired, so as to minimize the thickness of the oil film between the seal and the sealing surface and reduce the leakage of the seal.

forklift tilting cylinder seal leakage causes and countermeasures: a. Loose tie rod nut will cause leakage, tighten the tie rod nut according to the torque requirements of tie rod nut, test no leakage can continue to use. b. Pressure exceeding the limit will also cause leakage. Replace the forklift tilting cylinder seal and re-tighten the tie rod nut to reduce the pressure to the nominal pressure range of the forklift tilting cylinder. c. The forklift tilting cylinder seal is extruded, if the O-ring is obviously extruded at the forklift tilting cylinder seal, replace the forklift tilting cylinder seal.

Answers to some questions about forklift tilting cylinder:

What is the difference between hollow and solid oil cylinders?
Hollow solid cylinder, according to conventional understanding, refers to whether the piston rod is solid or hollow. General ordinary hydraulic cylinder, the piston rod is solid structure. Hollow hydraulic cylinder refers to a hollow piston rod structure of the hydraulic cylinder, see the attached figure. Piston rod hollow function: 1, the piston rod hollow, the middle can be threaded rod. For example, the clamping cylinder with a sawing machine, the piston rod center threading rod, part of the stroke through manual, part of the stroke hydraulic automatic walk. 2, the hollow hole of the piston rod can be used to direct the oil circuit to achieve special oil circuit. 3, the cylinder is relatively large, the piston rod is relatively large, and the stroke is longer, in this case, the piston rod is hollow to reduce the movement friction and lateral force.

Slide weight 35 kg exit stroke 55mm, is it suitable to use 40 cylinder diameter cylinder?
The maximum output force of the 40-bore hydraulic cylinder can reach 2 tons, and whether it can be used depends on the use scenario. In addition, the problem of mechanism stuck has nothing to do with the size of the power source, and reasonable structural design and good machining and assembly accuracy are the key.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
久久啪久久mm精品23| 色综合88| 最新国产毛2卡3卡4卡| h视频免费看| H番VA免费VA| 日韩偷拍久久| 中文字幕99| 国产精品久久久久久久久久麻豆| 国产精品JIZZ在线观看老狼| av日韩综合网| 欧美激情 - 右手影院| 中文字幕一区2区3区| 亚洲AV综合一区二区| 中文字幕一区日韩欧美| 最新国产成人无码久久| 人妻激情中文影片| v天堂在线| 真人在线一区日韩| 欧美日韩亚洲中文字幕一区二区| 新a色视频| 涩爱区综合| 五月天怡红院| 在线观看免费视频网站a站| 欧美国产激情三区四区五区| 亚洲精品一本在线| 欧美日韩高清成人电影| 亚洲精品久| 色综合久久影院| 亚洲 欧美 激情 小说 另类| 欧AV一区二区三区| 亚洲国产精品一区| 亚洲无码一级毛片| 开平市| 69式视频免费jizz| 人妻互换一二三区激情夏日彩春| 久久夜靖品2区| 嗯嗯嗯 中文字幕 无码| 国产,日韩,丝袜,欧美一区| 久久人人爽人人爽人人片亚洲| 97视频精品全国免费观看| 久久亚洲精品无码AV黑葡萄|