日女人逼,日韩av免费在线观看,AV小网站,奶水孕妇挤胸喷奶水AV

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

reset cylinder Sold to Turkey

Release time:2023-11-19 14:06:36 Hits: Current position: Home > News

This article mainly introduces:

Turkey hydraulic cylinder,reset cylinder manufacturer,reset cylinder

Turkey reset cylinder

(Turkey reset cylinder,produced by Hengyu Hydraulic Co., Ltd)

reset cylinder are widely used in Turkey,because of long service life,smooth movement,high work efficiency.So our company has designed reset cylinder for customers from Turkey.

Introduction to reset cylinder:

The piston seal of the reset cylinder is the main element to prevent leakage in the reset cylinder. For the lip seal, it should focus on checking whether the lip edge is bruised and worn, and for the combination seal, it should focus on checking the wear of the sealing surface, and then determine whether the seal can be used. In addition, it is necessary to check whether the static seal between the piston and the piston rod is crushed. The piston rod seal should focus on checking the wear of the seals and supporting rings.

The method of sleeve reset cylinder to improve the processing quality: there is a big gap in the service life of post-plating polishing and post-plating polishing, especially in mass production. Strictly clean the flying edge and burr of mechanical components, especially the edge of the sealing groove, and the tiny metal burr, strictly clean before assembly. The surface fatigue strength and stress corrosion resistance of the reset cylinder can be significantly improved by rolling in the finishing of the inner holes of the reset cylinder. The roughness of the surface of the friction pair is generally controlled between Ra0.4 and 0.8.

The repair method of reset cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

reset cylinder body inspection: The inner surface of the reset cylinder and the piston seal are the main factors causing the leakage in the reset cylinder, if the reset cylinder has a longitudinal tensile mark, even if the new piston seal is replaced, it can not effectively eliminate the fault, the inner surface of the reset cylinder mainly checks whether the dimensional tolerance and shape and position tolerance meet the technical requirements, there is no longitudinal tensile mark, and measures the depth of the longitudinal tensile mark, in order to take the corresponding solution.

Answers to some questions about reset cylinder:

How to calculate the hydraulic cylinder pressure? How much pressure can put up how much weight?
If you want to calculate the pressure of the cylinder, you must know the inner diameter of the cylinder, if the piston rod is needed to lift the weight, it should be: cylinder (no piston rod end) pressure = load (4000N) ÷{(PI /4)X the square of the cylinder diameter (mm) ", it has nothing to do with the piston rod diameter, the rod diameter of the piston rod is only related to the stability of the cylinder. The pressure inside the cylinder should be p=F/S=400×10/(3.14×(0.5×25)×(0.5×25))=8.15MPa which means that you need to provide at least that much pressure to complete the operation.

What does the maximum output force of the cylinder piston mean?
The maximum output of the cylinder is related to the pressure of the hydraulic system that you link to the cylinder. For example, the rated maximum output thrust of the MOB 50 cylinder is 1.3 tons and the rated pressure is 7Mpa. That is, when the input hydraulic oil pressure of the cylinder reaches 7Mpa, the maximum output thrust of the cylinder is only 0.98 tons. When the input hydraulic pressure is only 5Mpa, the maximum output thrust of the cylinder is 1.3 tons. Because the pressure of the cylinder limit is only 7Mpa, if the oil pressure of the input system exceeds 7Mpa, the cylinder can not withstand the pressure burst, and it is damaged.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
东京天堂热| 亚洲五月综合| 97色伦图片97综合影院| 久久综合九色综合欧美| 大香蕉一本| 国产精品久久久久的角色| 亚洲日韩欧美色| 老汉色av影院| 五月婷婷色亚洲| 久久日韩| 欧美牲交a欧美牲交aⅴ免费下载| 狠狠综合久久久久尤物丿| 国产色网址在线观看| 欧美日韩久久国产免费| 加勒比综合网| 涩爱 三区| 亚洲国产精品激情在线观看| 欧美激情综合久久| 小黄片久久久| 日日夜夜狠狠操| 欧美乱一区二区| 亚洲欧美国产日韩精品| 久久久久国产精品二区三区| 2019日本高清中文字幕在线| 无码精品久久久一区二区三区| 亚洲欧美日韩综合久久久| 奇米视频在线播放中文字幕| 日本久久精品一区二区三| 欧美i8一i6sa×性处| 婷婷五月天 在线激情| 免费视频在线中文字幕| 啊片在线| 国产伦一区二区三区| 人妻秘书痴汉电车| 无码精品人妻一二三区免费粉红| 亚洲熟女久久| 色呦呦免费在线观看| 香蕉久久AV一区二区三区| 久久综合精品视频| 六月婷婷在线| 有码第一页|